Metro Floor Mounting for Stationary Units Manuel d'utilisateur télécharger pdf

INSTRUCTIONS

ASSEMBLY

InterMetro Industries Corporation

North Washington Street, Wilkes-Barre, PA 18705

For Product Information Call: 1-800-433-2232

Visit Our Web Site: www.metro.com

Floor Mounting

Instructions for

Stationary Units

Fig. 1

Fig. 2

Single Wide Unit = 15

/16 (40.2 cm)

Double Wide Unit = 35

/8 (90.5 cm)

Triple Wide Unit = 55

/8 (140.6 cm)

Fig. 3

Base Replacement Parts:

PART NO. DESCRIPTION

RPF04-202A Qty. (1) Leveling Foot (

/8-16 x 2

/2 Lg.)

RPPLUG-4 Qty. (4) Hole Plugs (for

/2 Diameter Holes)

RPF04-216 Qty. (4) End Cap Screws (#8 x

/4 Tapping – Taupe HD)

RPF04-247 Qty. (4) Post Mounting Screws (

/16-18 x 1

/2 Lg.)

RPSXFLRBKT Qty. (1) Floor Bracket

FLOOR

MOUNTING

INSTRUCTIONS

For Stationary

Starsys

™

Units

This kit, Part No. SX-FLR, contains

two (2) brackets that allow the unit to

be anchored to a floor surface. No

mounting screws are supplied in this

kit due to the different types of floor

construction. You or your installer

must purchase the appropriate

fasteners suitable for the floor

conditions. The floor brackets can

accommodate screws or fasteners up

/4" inch diameter. Follow the

fastener manufacturer instructions

during assembly.

1. Move the unit into the desired

location against the wall.

2. Remove the lower drawers or

shelves. Refer to the user manuals for

details.

3. Unit is shipped with the leveling

feet fully retracted. The two rear

mounting feet must be extended 1

/4"

(32mm) before placing the unit in the

desired location. Extending the feet is

achieved by inserting a

/4" (6mm) flat

tipped screwdriver down into the holes

at the rear comers of the unit. Turning

the screwdriver clockwise will extend

the feet.

4. Slide the unit in place. On the floor,

mark the locations of the two rear

leveling feet. Move unit forward to

reveal marked feet locations.

5. Position floor brackets so the open

slot is facing forward and align with the

marked feet locations. See Fig 1. Verify

the center to center dimensions given in

Fig 1.

6. Match drill holes into floor using the

floor brackets as templates. Follow the

fastener manufacturer’s guidelines as to

drill size. Affix brackets to floor.

7. Slide unit back, aligning the feet with

the slots in the floor brackets, 1

/2"

(38mm). Slide unit back onto the floor

brackets, capturing the leveling feet

pads under the slots in the brackets

(Fig. 2). Lower unit by turning the rear

leveling screws counter-clockwise until

the base is about

/4" (19mm) off the

floor. Base frame must lock into the legs

on the bracket (Fig. 2).

8. Level the unit by using a

/4" (6mm)

flat tipped screwdriver and turning the

leveling screws clockwise to raise or

counter-clockwise to lower the unit

(Fig. 3).

NOTE: Do not raise the rear of the unit

more the 1" (25mm) off floor. The front

can be raised up to 2" (50mm).

9. Four (4) hole plugs are supplied with

each unit. Install a plug into each

leveling access hole.

10. Replace all removed components.

1 2 3 4

Résumé du contenu

Page 1 - MOUNTING

INSTRUCTIONSASSEMBLY®InterMetro Industries CorporationNorth Washington Street, Wilkes-Barre, PA 18705For Product Information Call: 1-800-433-2232Visit

Page 2 - DE MONTAGE

®TM®D’ASSEMBLAGEINSTRUCTIONSInstructions demontage au sol desmeubles stationnairesFig. 1Fig. 2Meuble simple = 40,2 cm (15-13/16 po)Meuble double = 90,

Page 3 - EL SUELO

®TM®DE ENSAMBLAJEINSTRUCCIONESInstrucciones demontaje en el suelopara unidades fijasFigura 1Figura 2Ancho de la unidad sencilla = 40,2 cm(15 13/16 pul

Page 4

®InterMetro Industries CorporationNorth Washington Street, Wilkes-Barre, PA 18705For Product Information Call: 1-800-433-2232Visit Our Web Site: www.m